Why Your Watch Runs Fast or Slow and What Seconds Per Day Means
Every watch keeps imperfect time. A quartz watch might drift by ten seconds in a month, while a perfectly healthy mechanical watch can gain or lose ten seconds in a single day.

Every watch keeps imperfect time. A quartz watch might drift by ten seconds in a month, while a perfectly healthy mechanical watch can gain or lose ten seconds in a single day. New owners of automatic watches often notice this within the first week, check the time against their phone and wonder whether something is broken. Usually nothing is. The watch is simply doing what mechanical watches do.
Understanding why a watch runs fast or slow, and what the accuracy figures on a spec sheet actually mean, makes it much easier to judge whether your watch needs a service or just a little patience.
What Seconds Per Day Actually Measures
Watch accuracy is usually expressed as seconds per day, written as s/d or spd. A rating of +6/-4 s/d means the manufacturer expects the watch to gain no more than six seconds or lose no more than four over 24 hours. It is a range, not a promise of a fixed amount. On Monday your watch might gain three seconds and on Tuesday lose one, depending on how you wore it.
The figure that matters day to day is the average over a week. A watch that gains an average of five seconds a day will be about 35 seconds fast after seven days, which most owners correct with a quick reset on Sunday evening.
Typical Accuracy by Watch Type
The movement inside the case sets the baseline. If you are not sure what kind of movement your watch uses, our guide to how a mechanical watch actually works explains the basics.
| Movement type | Typical accuracy | Per month |
|---|---|---|
| Standard quartz | About +/-0.5 s/d | About 15 seconds |
| High accuracy quartz | About +/-0.03 s/d | Under 1 second |
| Entry level automatic | -20 to +40 s/d | Several minutes |
| Mid range automatic | About +/-10 s/d | Up to 5 minutes |
| Chronometer certified | -4 to +6 s/d | 1 to 3 minutes |
These are manufacturer tolerances. Many watches perform better than their rating, and a few perform slightly worse when brand new before settling down.
Why Mechanical Watches Drift
A mechanical watch keeps time with a balance wheel that swings back and forth, usually between 6 and 10 times per second. A hair-thin spring controls the rhythm, and the escapement releases the gear train one step at each swing. Anything that changes how evenly that balance swings will change the rate.
Position
Gravity pulls on the balance differently depending on whether the watch is dial up, crown down or standing on its side. That is why watchmakers test in several positions. Many owners find their watch gains when lying flat overnight and loses on the wrist, or the reverse.
Power Reserve
A fully wound mainspring delivers more energy than one that is nearly empty. Most watches keep their best time in the first 24 hours after full wind and drift more as the reserve runs down. You can read more in our piece on what a watch's power reserve actually tells you.
Temperature
Metal expands slightly in heat and contracts in cold, which affects the balance spring. Modern alloys reduce this effect a lot, but a watch left on a sunny windowsill or worn skiing may still run differently for the day.
Things That Make a Watch Suddenly Run Fast
A sudden change, such as a watch that was steady at +3 s/d and now gains two minutes a day, usually points to one specific cause rather than general wear.
- Magnetism. This is the most common culprit. Laptop lids, phone cases with magnetic clasps, handbag closures and speakers can magnetise the balance spring, making its coils stick together and the watch run very fast.
- A hard knock. A drop can shift the balance or disturb the hairspring, which tends to cause erratic timing.
- Old oils. After five to eight years, lubricants thicken, the balance swings less freely and the rate becomes unstable. This usually shows as gradual losing rather than sudden gaining.
A magnetised watch can be fixed in minutes by a watchmaker with a demagnetiser, often for free or a very small charge. It is worth trying before booking a full service.
How to Track Your Own Watch
You do not need special tools to measure accuracy. Set the watch exactly to an atomic time source, such as your phone clock, at the same time each morning. Write down the difference every 24 hours for a week, wearing the watch as you normally would. Divide the total gain or loss by seven to get your average.
Some owners use free timegrapher apps that listen to the tick through the phone microphone. They give a quick reading but are sensitive to background noise, so treat the result as a rough guide rather than an exact figure.
Keep the log simple. A note on your phone with the date, the reading and how the watch spent the night is enough. After two or three weeks you will see a pattern, such as plus four seconds on work days and minus two on weekends spent mostly off the wrist. That pattern is far more useful to a watchmaker than a single reading taken on the counter.
Using Resting Position to Correct Drift
Once you know how your watch behaves, you can use its positional habits in your favour. If it gains on the wrist during the day, try resting it overnight in the position where it loses, often crown up or crown down. Over a week, the two can balance out to almost zero. It is an old trick that costs nothing and works surprisingly well for watches with a steady daily rate.
When Accuracy Means a Service Is Due
Drift alone is not a fault. Consider a watchmaker when you see any of these:
- The rate is well outside the manufacturer's tolerance for more than a week after demagnetising.
- The watch stops overnight even though it was worn all day.
- Timing jumps around by 20 seconds or more from one day to the next.
A regulation, where a watchmaker adjusts the rate without a full service, can cost far less than an overhaul if the movement is otherwise healthy.
FAQ
Is a mechanical watch that gains ten seconds a day faulty?
Not usually. Ten seconds a day is within the tolerance of many mid range automatic watches. It only becomes a concern if the watch has a tighter rating or the rate has suddenly changed.
Is it better for a watch to run slightly fast or slightly slow?
Most watchmakers regulate to run slightly fast, around two to five seconds a day, because people tend to prefer arriving early rather than late.
Can a quartz watch be magnetised too?
A strong magnet can stop a quartz watch's motor temporarily, but it usually recovers once moved away. Lasting effects are much less common than with mechanical watches.
The Takeaway
Seconds per day is a range, position and power reserve shape daily timing, and sudden large gains usually mean magnetism rather than damage. Track your watch for a week before deciding it needs work. For more on what happens inside the case, see our watch mechanics guides.
More in How Watches Work
How Watches Work
Watch Keyless Works: How the Crown Sets the Time
A reader sent me photographs last spring of a 1970s hand wound watch he had picked up at a house clearance for about 40 pounds.
How Watches Work
Watch Shock Protection and What a Drop Really Damages
A reader wrote to me last month after knocking his automatic off a bathroom shelf onto tiles.
How Watches Work
Tourbillon Watch Explained and Whether It Improves Accuracy
A tourbillon watch can cost more than a car, and the rotating cage behind its open dial is hypnotic to watch.