Watch Water Resistance Ratings and When to Test the Seals
A watch marked 50 metres sounds as if it could follow you down a modest dive. In reality, many watchmakers would advise you not to swim with it at all.

A watch marked 50 metres sounds as if it could follow you down a modest dive. In reality, many watchmakers would advise you not to swim with it at all. That gap between the number on the dial and what the watch can safely handle is behind a large share of the water damaged watches that reach repair benches every summer.
Watch water resistance is not a permanent feature. It depends on rubber gaskets, a crown and a case back that age, dry out and shift over time. Below I explain what the ratings really mean, how often the seals need checking, and the simple habits that keep moisture out of a watch you care about.
What Watch Water Resistance Ratings Really Mean
The figure on a case back is based on a pressure test in a lab, with the watch still and new. It is not a depth you can take it to while swimming, where movement, temperature changes and water jets add pressure. A practical reading looks like this.
| Marking | Realistic use |
|---|---|
| Water resistant, 30 m or 3 bar | Rain, splashes, washing hands. Not swimming. |
| 50 m or 5 bar | Brief, light swimming in calm water. No diving or jumping in. |
| 100 m or 10 bar | Swimming and snorkelling. Not scuba diving. |
| 200 m and above, or ISO 6425 diver marking | Recreational diving, watersports, regular water use. |
One more point: "water resistant" is the legal term in most markets. "Waterproof" has been discouraged for decades because no watch keeps out water forever.
Why Seals Wear Out Even if You Never Swim
Gaskets are small rings of rubber or synthetic material that sit under the case back, around the crown tube and sometimes under the crystal. Over three to five years they harden, shrink and lose their grip, whether the watch has been near water or not.
Several everyday things speed that up:
- Heat. Saunas, hot tubs and leaving a watch on a car dashboard in summer all dry out rubber quickly.
- Chemicals. Perfume, sunscreen, chlorine and salt water slowly attack gasket material.
- Sudden temperature change. Jumping from hot sand into cold sea makes metal and glass contract at different rates, opening tiny gaps.
- Opening the case. Every battery change disturbs the case back gasket. If it is not replaced or properly greased, the seal may never be quite the same.
How Often to Test Water Resistance
A pressure test is quick, usually 10 to 20 minutes, and many independent watch repairers charge somewhere between 15 and 40 in local currency for it. That is far cheaper than drying out a flooded movement.
My rough schedule for most owners:
- Once a year if you swim or shower with the watch regularly.
- Every two to three years for a daily wearer that rarely meets more than rain.
- After every battery change or case opening, no exceptions.
- Before a holiday where you plan to swim or dive, ideally a few weeks ahead.
Shops typically use a dry air pressure tester, which checks for leaks without getting the watch wet. Some also offer a wet test for dive watches. Ask which one they use and what pressure they test to.
Keep the test receipt with the watch papers. A short history showing the date, the pressure reached and any gaskets replaced is useful at the next service and reassures a buyer if you ever sell. For a watch worth several hundred or more, that record often adds more confidence than any claim in a listing, and it costs nothing to keep in the original box.
The Advice I Think Is Overcautious
A popular rule says you should never wear any mechanical watch near water, even if it is rated to 100 metres. I find that too strict. A well maintained watch with fresh gaskets and a screwed down crown was designed for exactly that use, and treating it like glass ignores what the maker built it for.
The opposite mistake is far more common, though. Owners of vintage pieces assume the original rating still applies. A watch from the 1970s marked 100 metres, with original gaskets, should be treated as having no water resistance at all until a watchmaker has resealed and tested it. The number on the back describes the watch as it left the factory, not as it is today.
Daily Habits That Keep Water Out
Most water damage comes from small, avoidable slips rather than deep dives.
Check the crown every time
If your crown screws down, make sure it is fully tightened before any contact with water. A crown left pulled out after setting the time is the classic cause of a flooded watch.
Never use buttons underwater
Chronograph pushers and crowns should not be pressed while wet unless the manual says they are designed for it. Pressing them opens a path for water.
Rinse after the sea or pool
A quick rinse in fresh, lukewarm water removes salt and chlorine before it dries on the gaskets. Then pat dry with a soft cloth. These steps fit into the wider routine in our guide on caring for a watch so it lasts.
Signs That Moisture Has Already Got In
Act quickly if you notice any of these. Water spreads corrosion through a movement within days.
- Fog or droplets on the inside of the crystal, especially after a temperature change.
- Rust spots or discolouration on the dial or hands.
- A sudden change in timekeeping, or a quartz watch stopping soon after water contact.
Take it to a watchmaker the same week. Do not try drying it with a hair dryer or leaving it on a radiator; the heat can damage gaskets and lubricants further. If you are thinking about a watch built for regular water use, our explainer on what makes a dive watch covers the features worth paying for.
FAQ
Can I shower with a water resistant watch?
It is better not to, even with a high rating. Hot water, soap and steam age gaskets quickly. If you do, choose a watch rated to at least 100 metres with recently tested seals.
Does a new watch need a water resistance test?
Not straight away. It was tested at the factory. Start the schedule after its first battery change or service, or after two to three years of wear.
How much does replacing gaskets cost?
For most watches, replacing the case back and crown gaskets during a test is inexpensive, often a small addition to the test fee. Full resealing during a service costs more but is usually included in the price.
A Simple Rule to Remember
Treat the rating as a maximum for a well sealed watch, not a promise. Have the seals tested every few years, always after the case is opened, and check the crown before every swim. A ten minute test now protects a movement that would cost far more to repair. You can find more maintenance guides in our care section.
More in Watch Care
Watch Care
Do You Need a Watch Winder for an Automatic Watch
I bought a two slot winder before I owned two automatics worth winding.
Watch Care
Quartz Watch Battery Replacement and When to Do It
A quartz watch that stops in a drawer usually gets left there.
Watch Care
Leather Watch Strap Care and How to Make a Strap Last Longer
A new leather strap can look tired within one summer: dark sweat marks near the buckle, a stiff crease at the holes, and a...