ISO INTERNATIONAL 8117 STANDARD Second edition 2003-02-15 Textile machinery Knitting machines Nominal diameters of circular machines Materielpourlindustrietextile-MachinesatricoterDiametres nominauxdesmachinescirculaires Reference number ISO 8117:2003(E) ISO @ISO2003 ISO8117:2003(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO copyright office Case postale 56.CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland !! @ISO2003—Allrightsreserved ISO 8117:2003(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies InternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization adopted by the technical committees are circulated to the member bodies for voting. Publication as an InternationalStandard requiresapprovalbyat least75%of thememberbodiescastingavote rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO8117 was prepared by Technical Committee ISO/TC72,Textile machinery and machinery for dry- cleaning and industrial laundering, Subcommittee Sc 3, Machinery for fabric manufacturing including preparatorymachineryandaccessories. This second edition cancels and replaces the first edition (isO 8117:1986), which has been technically revised. ISO 8117:2003(E) INTERNATIONALSTANDARD Textile machinery Knitting machines Nominal diameters of circularmachines 1 Scope This International Standard specifies the nominal diameters of circular knitting machines and the numerical designations corresponding to the size of the machines. It is applicable to small- and large-diameter circular knitting machines and to sinker machines. Normativereferences 2 The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Iso7839,Textilemachineryandaccessories-KnittingmachinesClassificationandvocabulary Iso8188,Textilemachineryandaccessories-Pitchesofknittingmachineneedles 3 Nominal diametersand numerical designation For classifications and the vocabulary ofknitting machines, see IsO7839; for needle pitches, see IsO8188. Table 1 specifies the nominal diameter, in millimetres, and the numerical designation applicable to each machine size. ISO8117:2003(E) Table 1Circular knitting machines Small circular Large circular knitting machines knitting machines Designation Nominal diameter Designation Nominaldiameter 57 2 1/4 178 7 64 2 1/2 190 7 1/2 70 2 3/4 203 8 76 3 229 9 83 3 1/4 254 10 89 3 1/2 279 11 95 3 3/4 305 12 102 4 330 13 108 4 1/4 356 14 114 4 1/2 381 15 121 4 3/4 406 16 127 5 432 17 133 5 1/4 457 18 140 5 1/2 483 19 146 5 3/4 508 20 152 9 533 21 165 6 1/2 559 22 584 23 610 24 635 25 660 26 711 28 762 30 (787) (31) 813 32 (838) (33) 864 te 914 36 996 38 1 016 40 1 067 4