BS ISO 17458-5:2013 BSl Standards Publication Road vehicles FlexRay communications system Part 5: Electrical physical layer conformance test specification bsi. ..making excellence a habit. BS ISO 17458-5:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 17458-5:2013. The UK participation in its preparation was entrusted to Technical Committee AUE/16, Electrical and electronic equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2013. Published by BSI Standards Limited2013 ISBN 978 058076716 6 ICS 43.040.15 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013. Amendments issued since publication Date Text affected BS ISO 17458-5:2013 INTERNATIONAL ISO STANDARD 17458-5 First edition 2013-02-01 Road vehicles— FlexRay communications system Part 5: Electrical physical layer conformance test specification Véhicules routiers -Systeme de communications FlexRay Partie 5: Spécification d'essai de conformite de la couche d'application électrique Reference number ISO 17458-5:2013(E) @ ISO 2013 BS ISO 17458-5:2013 ISO 17458-5:2013(E) COPYRIGHTPROTECTED DOCUMENT icensed ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland = @ ISO 2013 - All rights reserved BS ISO 17458-5:2013 ISO 17458-5:2013(E) Contents Page Foreword. Introduction. .vi 1 Scope. 2 Normative references.. 3 Terms, definitions, symbols and abbreviated terms 3.1 Terms and definitions .... 3.2 Abbreviated terms..... 4 Document reference according to Osl model .... 5 Conventions.. 5.1 5.2 Notational conventions 6 Test environment.. 6.1 Test case architecture.. 6.2 6.3 Test environment. 6.4 Test topology .. 6.5 Test equipment .... 27 7 Stress Conditions 34 7.1 Ground shift......... 7.2 Low battery voltage inside operational range ... .35 7.3 Undervoltage... 36 7.4 Dynamic low battery voltage... 37 7.5 Dynamic low supply voltage . 7.6 Failures... 41 7.7 Babbling idiot.. 47 7.8 7.9 EMC.... 48 7.10 ESD 48 7.11 Temperature tests 48 7.12 Common mode offset. 8 8.1 General 49 8.2 Static test cases 50 8.3 Communication 8.4 Host Interface. 54 8.5 Mode 55 8.6 Power supply 59 8.7 8.8 Dynamic low battery voltage.. 62 8.9 Dynamiclow supplyvoltage 62 8.10 62 8.11 Functional class . 8.12 Simulation .... 65 9 Test Cases for Bus Drivers.. 65 9.1 Configuration, 66 9.2 Static test cases 9.3 Test cases . 97 @ ISO 2013 - All rights reserved ili BS ISO 17458-5:2013 ISO 17458-5:2013(E) Contents Page Foreword. Introduction. .vi 1 Scope. 2 Normative references.. 3 Terms, definitions, symbols and abbreviated terms 3.1 Terms and definitions .... 3.2 Abbreviated terms..... 4 Document reference according to Osl model .... 5 Conventions.. 5.1 5.2 Notational conventions 6 Test environment.. 6.1 Test case architecture.. 6.2 6.3 Test environment. 6.4 Test topology .. 6.5 Test equipment .... 27 7 Stress Conditions 34 7.1 Ground shift......... 7.2 Low battery voltage inside operational range ... .35 7.3 Undervoltage... 36 7.4 Dynamic low battery voltage... 37 7.5 Dynamic low supply voltage . 7.6 Failures... 41 7.7 Babbling idiot.. 47 7.8 7.9 EMC.... 48 7.10 ESD 48 7.11 Temperature tests 48 7.12 Common mode offset. 8 8.1 General 49 8.2 Static test cases 50